Essential Plumbing Guide for Bathtub Installation
Essential Plumbing Guide for Bathtub Installation
Blog Article
Just about every person has got their own unique way of thinking in relation to A Step-by-Step Guide to Installing a Bathtub.
Setting up a bathtub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably challenging job. If the old tub is conveniently available, the project can relocate immediately; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to move out the old tub as well as set in the brand-new one. Make sure you have actually certified on your own for the task and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed project, it is far better to think about using one before you start. Possibilities are you may require a professional plumber to make tube connections.
This write-up will help you install a brand-new bathtub in your restroom if you have already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of eliminating the existing taps can be rather troublesome due to the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the tap and also the various other end provides a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Protect the tap in position with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular faucet connectors. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wood boards under its feet, position the bath tub in the called for setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level reviews degree.
To mount taps, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water and inspect all joints as well as new pipework for leakages and also tighten them if needed. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Finally, deal with the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub needs to wait until the bath tub has been made use of a minimum of once as this will certainly settle it right into its final placement.
Getting ready for the Installment
First of all, the sustaining framework supplied with the bathroom must be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps system to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you utilize all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a rigid seal, triggering the water to penetrate the wall in between the bathroom as well as the tiling, bring about issues with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, as well as can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealant can crack rather very early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the market. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Hopefully you enjoyed reading our piece on A Step-by-Step Guide to Installing a Bathtub. Many thanks for taking a few minutes to read our short article. Loved our posting? Please share it. Let others discover it. We enjoy reading our article about How to Install a Bathtub.
Act now! Report this page